ALWAZEN INDUSTRIES

ALWAZEN INDUSTRIES / TECHNICAL CATALOGUE

Industrial cardan shafts

Configurations, reference dimensions and drive requirements. From the existing assembly to an agreed industrial shaft specification.

Explore the technical range Discuss an industrial shaft Measure the shaft and both connections
S / M / L / XL / XXL / XXL+24 SERIES / 49 FLANGE VARIANTS02 / 06.10.2026

PDF catalogue · EN / AR / RU

تنزيل الكتالوج · AR Download catalogue · EN Скачать каталог · RU

Reference series and dimensions from WiCHMANN Industry Catalogue 2023. They describe the source range, not certified ALWAZEN ratings or confirmed stock. Final selection, supply and acceptance are agreed for each project.

Designed around the drive

The duty cycle matters as much as nominal torque. Specify the equipment, load history and environment before selecting the assembly.

01

Steel & rolling mills

Main and auxiliary drives, reversing duty, roll changes and high shock loads.

02

Paper & printing

Continuous running, vibration control, alignment and bearing-life requirements.

03

Pumps & process machinery

Speed, service life, installation geometry and ambient conditions.

04

Rail & heavy equipment

Changing geometry, dynamic loads and defined acceptance requirements.

05

Cranes & handling

Intermittent cycles, starts, braking and reversing operation.

06

Test stands & machines

Defined torque/speed envelope, mounting space and measurement requirements.

Seven reference configurations

Design numbers below identify the original reference configurations. They are not ALWAZEN part numbers.

Reference series

This catalogue covers a source product range. Workshop capacity, stock, delivery and the acceptance of a specific shaft are confirmed separately.

Series shown: 24

Source reference / WiCHMANN 2023
Reference seriesFamilyØ / mmMl / NmMw / NmGl / Nm
07600S76600300220
10000M1001 400700660
11600M1163 0001 500990
12600M1265 3002 3001 780
14400M1446 0002 9002 070
15800L1588 8004 4002 400
17200L17212 5005 1003 500
17800L17817 0008 5004 600
20400L20420 00011 0006 800
21500XL22026 00013 0008 050
21510XL22029 00014 5008 350
22580XL22545 00023 00012 050
25080XL25070 00035 00018 650
28580XL285100 00050 00026 200
31510XL315143 00070 00028 140
35000XXL350210 000100 00040 300
39000XXL390300 000150 00056 800
44000XXL440500 000250 00081 500
49000XXL490700 000345 000112 000
55000XXL5501 000 000500 000154 000
62000XXL6201 250 000625 000210 000
68000XXL+6801 950 000950 000320 000
75000XXL+7502 650 0001 350 000750 000
84000XXL+8403 900 0001 850 0002 230 000

Ml = bearing torque; Mw = reversing fatigue torque; Gl = joint performance factor. Ml is not a continuous service torque. The source does not tabulate pulsating fatigue torque Ms here.

تنزيل الكتالوج · AR Download catalogue · EN Скачать каталог · RU

Define the working length

L1 is the compressed length. L2 is the maximum possible length compensation. The working length is the distance between the drive and output interfaces. For a fixed shaft, confirm the interface-to-interface dimension on the agreed drawing.

The source gives EBLopt = L1 + 0.5 × L2. Treat this as an initial layout reference; minimum spline engagement and the permitted operating stroke need engineering confirmation.

EBLopt = L1 + 0.5 × L2

Industrial shaft / project brief

Send the information available. Missing data can be identified during the technical review.

  1. Equipment / application / existing part marking

  2. Nominal, maximum and reversing torque; power

  3. Operating / maximum speed; duty cycle

  4. Compressed, installed and maximum length; stroke

  5. Flange drawings: DF, DC, PCD, DB, N and key / teeth

  6. Angles in both planes; phasing; bearing positions

  7. Temperature, contamination, lubrication and guarding

  8. Existing damage, vibration history and photographs

  9. Quantity, drawing revision and requested delivery date

  10. Acceptance criteria, balance requirement and documents

Discuss an industrial shaft

Measure the shaft and both connections

Record ends A and B separately. Keep the same end names in photographs, drawings and the request.

Schematic only; all dimensions in mm. Lc is the overall cross span, d the bearing cup diameter. Mark the measurement convention on the actual drawing.

Lz / Lf is the fully compressed interface-to-interface length; EBL / LE is the installed length. Required travel S / X does not establish permitted spline engagement. Confirm the usable stroke on the drawing.

SAE, DIN and XS names are identification clues. Record male or female centering, bolt geometry and any face teeth for each end. Confirm Mechanics / Wing-Style geometry from its own drawing.

Configurations and connection styles

Choose the arrangement before choosing a reference series. These categories describe the drive, not confirmed stock.

01

Telescopic

Specify compressed length, installed length and required travel.

02

Fixed length

Specify the interface distance and installation space.

03

Short coupling

Record the minimum mounting envelope and both connections.

04

Multi-section

Provide section lengths and positions of intermediate supports.

05

Double Cardan

Confirm centering, joint geometry and permissible operating angles.

06

Wing-Style / Mechanics

Identify the attachment geometry; flange diameter alone is insufficient.

Selection also needs load history, shock and reversing duty, speed and both joint angles. Agree lubrication and inspection intervals for the selected assembly. For vibration, record speed, load, onset and previous repairs; balancing does not replace defect inspection.

For off-highway equipment, identify the machine: wheel loader, telehandler, harvester, forestry or mining equipment.

Prepare the technical data

Fill the known values; unknown fields can stay blank. This worksheet prepares a local brief for review.

Length and assembly
Length and assembly
Connection A
Connection A
Connection B
Connection B
Operating data
Operating data

Continue to the service request

This step does not send a request. Review the brief and add contact details on the next page.

Technical references

Reference tables retain WiCHMANN 2023 identifiers. Additional sources inform measurement and selection checklists. They do not establish supplier authorization, interchangeability or ALWAZEN performance ratings. Confirm current requirements and drawings for the project. Reviewed 06.10.2026.